Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Blog Article
The publisher is making a few great points about A Step-by-Step Guide to Installing a Bathtub as a whole in this content below.
Setting up a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and often, tiling abilities. Changing an old tub with a new one is also a moderately tough task. If the old bathtub is conveniently available, the job can move easily; if you need to open a wall to remove the old bathtub and also place the new tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. Ensure you have actually qualified on your own for the task as well as fit trying it. As opposed to working with a professional to take control of a halfway-completed project, it is far better to consider utilizing one prior to you start. Opportunities are you might need a specialist plumber to make tube connections.
This post will certainly assist you set up a brand-new bath tub in your shower room if you have actually currently gotten a brand-new bathtub and also don't require to transform the setup of your previous water pipelines.
Your devices as well as product checklist need to make up the following:
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps unit to stop pressure on the bathtub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be quite troublesome due to the limited access that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub until the spirit level checks out degree.
To mount faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the supply of water as well as check all joints and new pipework for leakages and tighten them if required. Fill up the bathtub as well as additionally check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub ought to wait until the tub has been utilized a minimum of once as this will settle it right into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location in between the faucet and the sink. Safeguard the faucet in position with the producer supplied backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind needs to be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, bring about problems with dampness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are offered in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water before securing, to allow for the activity experienced when the tub is in use. The sealant can fracture relatively very early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily readily available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that write-up about How to Install a Bathtub from an acquaintance on a different web blog. Enjoyed reading our piece of writing? Please share it. Help another person find it. I am grateful for your time. Visit us again soon.
Dial, we'll handle! Report this page